gordon setter Posted January 18, 2014 Share Posted January 18, 2014 Kan noen hjelpe. Er på fjellet nå og har tatt med drillingen for å skyte inn den. Men får det ikke gjort da jeg ikke får gå videre ned på knep på kikkertsiktet. Den stopper ved zero stoppen. Hva gjør jeg ligger sikkert 20 knep for høyt nå. Har en 2,5-15x44 swarovski z6 jeg skal skyte inn. Quote Link to comment Share on other sites More sharing options...
jaktplussfiske Posted January 18, 2014 Share Posted January 18, 2014 Får du løsnet kikkertringene, kan du legge noe oppi ringen fremme, under kikkerten. F.eks litt tilskjært ølboks blikk eller noe annet du har med. Skrevet i beste hensikt, forstå det den som vil. Quote Link to comment Share on other sites More sharing options...
Bluto Posted January 18, 2014 Share Posted January 18, 2014 Du kan vell løfte den ringen som har "zero stopp" markering (den som de tre andre ringene er montert på) og justere deg videre ned over for å komme lavere. Regner med at du stopper mot merkinga som indikerer for innskytings avstanden og ikke at du trenger å "tilte" kikkerten. http://aa.swarovskioptik.com/download/pdf/Manuals_BT.pdf Quote Link to comment Share on other sites More sharing options...
Carlsen Posted January 18, 2014 Share Posted January 18, 2014 Har du fjernet ringene å løftet av sjølve "tårnet"?Om du ikkje har det,ligger det ett hjul under der som du justerer for å få meir klikk oppover,flytte Zero stopen.Dårlig forklart,men du skjønner det om du opner det.Då vil du sjå med ein gong kva du må gjere for å få det til å fungere Quote Link to comment Share on other sites More sharing options...
gordon setter Posted January 18, 2014 Author Share Posted January 18, 2014 Ja har gjort det. Og opp går men ikke ned. Får det ikke til altså. Plundra med dette i min timer nå. Quote Link to comment Share on other sites More sharing options...
Bluto Posted January 18, 2014 Share Posted January 18, 2014 Håper dette hjelper deg http://www.eurooptic.com/swarovski-bt-ballistic-turret-instructions.aspx Step 1: Unscrew the cap of the ballistic turret using the key supplied or an adequate coin. Step 2: Use the graduated dial by pulling upwards. Step 3: You will now have the 5 removable parts in front of you. All other parts are affixed to the rifle scope. Step 1: Sight in the elevation by turning the top section of the dial as shown in figure 01. If you are sighting in at 100 yards, turn to the right or left until your elevation is dead on at 100 yards. This will become the zero setting during further assembly. To do this, turn the upper detent ring in the required direction. Use the keyring opener if necessary. Step 2: After sighting in to your desired zero setting, turn the lower section of the dial in a clockwise direction until it stops as shown in figure 02. Step 3: Attach the coupling © on top of the dials so that the arrow on the coupling lines up with the white dot at the base of the turret. You have now made the setting for your desired zero range. If procedure 02 was followed, the coupling will always stop at this zero setting when the turret is turned clockwise. Step 4: Please check whether the entire control range (just under 360°) is accessible. To this end, turn the coupling in a counterclockwise direction all the way to the end stop. Now turn the coupling back again to the end stop. Step 5: For your second down range distance, turn the coupling in a counterclockwise direction by the necessary number of clicks and attach the (green) marking ring (B1) so that the green dot is directly above the white dot on the base of the turret. The necessary number of clicks can be determined by the BT Ballistic Calculator on our web site, by sighting in at the desired down range distance or by calling customer service at 570-220-3159. Step 6: Your third (yellow marking ring) and fourth (red marking ring) down range distances can be determined in the same way as you made them in section five. (See Sight In Example at the end of the tutorial.) Step 7: Now turn the entire turret in a clockwise direction all the way to the end stop at the zero setting. Step 8: Attach the cap (A) such that the directional tab lines up with the arrow and with the dot on the rifle scope. The cap can be screwed on with the key that was supplied. Your ballistic turret is now ready for use. Quote Link to comment Share on other sites More sharing options...
gordon setter Posted January 18, 2014 Author Share Posted January 18, 2014 Går nok ikke nå heller. Har ikke mer å gå på på knepp ned siden den stopper på zero stoppen. Quote Link to comment Share on other sites More sharing options...
Bluto Posted January 18, 2014 Share Posted January 18, 2014 Den er 2 delt og du justerer bare på den øverste, tror ikke du trenger "spesial" verktøyet fra Swarovski for å gjøre dette. Video link " target="_blank Quote Link to comment Share on other sites More sharing options...
1983 Posted January 18, 2014 Share Posted January 18, 2014 Om den stopper mot zero stop, så kan jo denne flyttes med fingrene. Om du ikke mere klikke igjen på kikkerten, så er det noe helt annet. Quote Link to comment Share on other sites More sharing options...
gordon setter Posted January 18, 2014 Author Share Posted January 18, 2014 Tror rett og slett det er det jeg ikke har. Og da må de jeg har kjøpt den av finne en løsning. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.