Grizzly Posted April 5, 2008 Share Posted April 5, 2008 Om ikke lenge får jeg omsider en Tikka T3 Lite SS i posten. Jeg har lest noe om at man bør skyte forsiktig de første skuddene, og gjerne pusse innimellom. Dette for at løpet skal "gå seg til". Hvordan skal jeg gå frem? - Hvor mange skudd, og hvor ofte skal det pusses? - Hvordan skal det pusses, helt rent, med bronsjebørste, solvent eller bare olje? Det er vel ikke noen eksakt vitenskap på dette, og om man ikke gjør det "helt etter boka" vil man trolig ikke merke det. Mange mener vel dette også er tull. Men uansett har jeg nå lyst til å være føre var. Quote Link to comment Share on other sites More sharing options...
КГБ Posted April 5, 2008 Share Posted April 5, 2008 God morgen store brunbjørn! I skytekammeret, under rifleskyting ligger det en tråd om å brekke inn løp. Der diskuteres dette. Du kan jo lese denne. Lykke til!! Quote Link to comment Share on other sites More sharing options...
sakotrg Posted April 5, 2008 Share Posted April 5, 2008 Her får du like mange svar som det finnes Kammerater Min metode.. Puss pipa helt rein med Remington Bore Cleaner, avslutt med olje og puss helt tørt. 1 skudd-> puss helt rent, x3 3 skudd-> puss helt rent, x3 5 skudd-> dra gjennom en lapp med olje og se om pipa mantler. Gjør den det fortsetter du litt til. Jeg skyter seriene i rolig tempo så ikke pipa blir varm . Noen piper mantler uansett, men pipene i T3en er bra så du trenger nok ikke bekymre deg for mye. Noen har et hysterisk, nesten religiøst forhold til det å brekke inn piper i våpen. Jeg har prøvd andre metoder enn den jeg nevner over, og jeg har pusset rent og skutt i vei uten å tenke noe over det. Konkslusjon: Alt med måte.. mantler ikke pipa er det bare tull å pusse mellom seriene. (Mantelen ser du veldig lett om du pusser helt rent med olje, bommene får samme farge som kulene) Lykke til med ny rifle! Quote Link to comment Share on other sites More sharing options...
Grizzly Posted April 5, 2008 Author Share Posted April 5, 2008 Takker Regnet med at det stod noe her, men kunne ikke finne det. Quote Link to comment Share on other sites More sharing options...
HS Precision Posted June 12, 2009 Share Posted June 12, 2009 Her er en flott videoprosedyre av innbrekking av løp for presise skudd; Quote Link to comment Share on other sites More sharing options...
pettern Posted June 12, 2009 Share Posted June 12, 2009 ja detta var en grei "brekking" av løp, Tror jeg tar meg arbe det er med og pusse med olje og bronsebørste mella di første 5 enkelt skudda,og mantelfjerner bremserens og så nytt skudd. er nok mange som aldri har pussapipa og,rust i krona og mantel i løpet,Men det smell og da er dem fornøyd. Quote Link to comment Share on other sites More sharing options...
Grim Posted June 12, 2009 Share Posted June 12, 2009 Dette er sakset fra Border barrel`s hjemmeside, ikke akkurat den dårligste løpsprodusenten.... 'SHOOTING IN' A BARREL There is much discussion about 'shooting in' a barrel. Everybody seems to have their own way of doing it, so this is a brief monograph about how we do it. But first, a few words on why 'shooting in' a barrel is necessary. No matter how well lapped or how finely finished the internal surface of the barrel is, the first few bullets down the barrel seem to leave a significant fraction of themselves behind as heavy metal fouling. A subsequent bullet shot up a barrel with heavy metal fouling will tend to press that fouling into the barrel causing dints and roughness in a bore that the barrel maker has gone to a lot of trouble to make smooth and even. So it is important to get all that metal fouling out before shooting another bullet up the barrel. When we shoot in a barrel, we fire one shot and then use a phosphor bronze brush and Shooters Choice to clean the barrel of powder fouling and loose dirt. Having dried out the barrel with a few patches, we squirt some Forrest bore foam up the barrel and leave it sitting for 24 hours to get out all the metal fouling. There is no way to quickly clean metal fouling out of a barrel and we find Forrest bore foam seems to do the job best as the foam clings to the whole interior surface of the barrel. After 24 hours the Forrest bore foam has turned dark blue, but all traces of the metal fouling is gone. Now we fire another shot and repeat the process. We do this about five times. Finally, we fire five shots and then give the barrel a final 24 hour soak in Forrest bore foam. The bore of the barrel will now have been 'conditioned' and metal fouling should be minimal from now on. Yes, we take a week to shoot in a barrel! But there is no quick way to remove heavy metal fouling. Anyone that says there is doesn't have a bore scope! Using moly coated bullets seems to minimise the metal fouling during this shooting in process and makes it all a lot easier. For general cleaning after shooting, we use a phosphor bronze brush dipped in Shooters Choice. This is pulled down the barrel from the muzzle a few times to loosen off the powder fouling. The barrel is then cleaned out using dry patches. It is important that the phosphor bronze brush is clean and in good condition. It should be kept in container so that does not pick up any sand and dirt. If the brush collapses on one side, as some makes tend to do, then throw it away and use a new one. A phosphor bronze brush will do no harm to your barrel provided it is free of dirt and in good condition. It is also important to clean out the chamber and the area in front of the locking lugs, just behind the back of the barrel. I should just say at this point that we are getting no favours or promotional payments for mentioning Forrest bore foam or Shooters Choice. I mention these products because that is what we use - for now. Someday, we may find something that we like better for one reason or another and then we will use that instead Quote Link to comment Share on other sites More sharing options...
Primer Posted June 13, 2009 Share Posted June 13, 2009 Her er en flott videoprosedyre av innbrekking av løp for presise skudd; Quote Link to comment Share on other sites More sharing options...
Xprez Posted June 13, 2009 Share Posted June 13, 2009 Her er en flott videoprosedyre av innbrekking av løp for presise skudd; Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.